Lodar 6 Function FET Receiver/Air Actuator + Standard Transmitter NOTE: This is for trucks that are fitted with an air compressor. "Two Functions" means two directions of a single action, such as winch in and out.  Operate your hand lever controls with Lodar’s actuator series. An air compressor with at least 110-120 psi is required for proper operation. This Lodar 2 function system features FETS, wide band, standard output, standard transmitter and an integrated actuator system. Five year pro-rated warranty.

INCLUDES

• 1 x Standard Transmitter
• 3 x Air Actuators
• 1 x Actuator Receiver with Wiring Harness and Glands
• 1 x Lo-Cover
• 1 x Lanyard
• 1 x Instructions

ACTUATOR SPECIFICATIONS

FEATURES
Soft-Start | a flow control valve in the supply line allows adjustment of the air supply into cylinder, hence the speed at which it moves. This gives a degree of “feel” to the system when “inching” equipment, without restricting the exhaust flow from the cylinder but also allowing immediate shut off.
Manual over-ride | this is available at all times. At rest, both pipes to the cylinder are “open to atmosphere”, allowing for free movement of the piston, with return to center when the system is deactivated.
ASSEMBLY
Air Cylinder(s) 32mm(1.25″) bore x 50mm(2″) stroke Fitted with trunnion and clevis, with lug(s) ready for welding 2 push fit elbows per cylinder
CONTROL BOX
Radio Receiver with outputs to valves – prewired
Flow control valve
3ft lengths of output pipe with push fit connections to the cylinder(s) – color coded for each pair of functions.
6ft length blue supply pipe fitted with 1/4″ adaptor (push fit)
8ft twin core power supply cable
STANDARDS
Max air pressure	120psi
Air requirements	Must be CLEAN and DRY (air flow is minimal)
Max push	149 lbs @120psi
Max pull	128 lbs @120psi
Voltage	12 and 24 Volts available (24 Volt systems are suffixed 24 – e.g. 92 1 50/24 etc)

 

TRANSMITTER SPECIFICATIONS

SWITCH TYPE
Type			Tactile Dome
BATTERY
Type			9V Alkaline Manganese (GP 1604A – JIS 6LF22 – IEC 6LF22 – Eveready 522 – Duracell MN1604)
CURRENT DRAW
Quiescent			15 micro amps
Operating			20 milliamps
PROTECTION
IP Rating			55
Registration codes			Over 16 million
PERFORMANCE
Temp Range			-10o C to + 40o C (13o F to + 104o F)
Range Nominal			60 meters (200 ft) from the Receiver, when driving a momentary output without signal drop out
Transmitted power			1 mW Typical
COMPLIANCE
EMC			Exceeds ETSI 300 220. Compliant E11 10R-037601
Modulation			FM
Frequencies			418.00 MHz F1D  USA (optional UK)
			433.92 MHz F1D World wide (optional USA)

 

RECEIVER SPECIFICATIONS

SWITCH TYPE
Output Switching			MOS Field Effect Transistor (P Channel Power MOSFET)
SUPPLY VOLTS
Nominal			12/24 Volts DC
Absolute Maximum			40 Volts DC
Minimum			8 Volts DC
Output Switch Supply			Internal 12/24 Volts
AMPS
FET Rating			15 Amps
System Rating			15 Amps
Quiescent Current			25 mA on Standby (Not SET)
Overload Protection			15 Amps (Auto Shutdown)
AERIAL
Internal Antenna			Yes Supplied and fitted
External Antenna			Optional See Accessories    Aerial Kit with 3 m Coax (9863)
OUTPUTS
Master			1   Can be Parallel or Continuous.
Function			6/7
PERFORMANCE
Simultaneous Outputs			Yes   With horizontal interlocks (Interlocks are programmable)
Instant TX response			Yes   No perceivable delay between TX operation and RX action
DIAGNOSTICS
LED’s			Yes   Confirm 5 Volts, SET, Fault and all Outputs.
PROTECTION
ESR Safety			Yes   See ESR Safety document
Back EMF			Yes   Diode protected on all outputs
Registration codes			Yes   Over 16 million
STOP Connection			Yes   Internal Emergency Stop Connection.
WIRING
Wiring Loom			Yes   3 meters (10ft) supplied and fitted
Cable Gland			Yes   Supplied and fitted
Connections			Screw terminal into plug and socket on PCB, for easy “swap out”
ENCLOSURE
Weight			0.3 lbs (335gms)
Lid			Smoke PVC – to view LEDs
Base			Black PVC
Breather			Gortex fitted in base
Mounting			4 external lugs
Fixings			5mm (3/16”) not supplied
IP Rating			Performs to IP67 standard (0.5 meter water for 1 hour)